Development of epoxy/BN composites with high thermal conductivity and sufficient dielectric breakdown strength part II-breakdown strength

Zengbin Wang, Tomonori Iizuka, Masahiro Kozako, Yoshimichi Ohki, Toshikatsu Tanaka

Research output: Contribution to journalArticle

57 Citations (Scopus)

Abstract

The aim of this research is to find a way to achieve the epoxy composites with high thermal conductivity and acceptable dielectric breakdown (BD) strength. A value 12.3 W/m·K is the highest thermal conductivity obtained for epoxy composite in Part I. Dielectric breakdown performances such as short-time dielectric breakdown strength (BD strength), partial discharge (PD) resistance and BD time for composites were investigated in the Part II. In general, micro filler inclusion will increase thermal conductivity and decrease dielectric breakdown performance. Influencing factors are considered to be the orientation of filler, the content of void space, the content ratio in the case of co-mixing, the addition of nano filler, and filler surface modification. Twenty six kinds of composites were prepared in consideration of the above influencing factors. There are two options for most appropriate ones among the composites evaluated in the research. One is an epoxy/ conglomerated h-BN composite with co-loaded nano SiO 2 and micro AlN filler. It has 12.3 W/m·K in thermal conductivity, 75.1 kV peak/mm in BD strength and 260 % of BD time for neat epoxy. It is most suitable when low BD strength and high thermal conductivity is needed. The other one is an epoxy/ h-BN composite with co-loaded nano silica and AlN filler for requirement of very high BD strength but lower thermal conductivity. Optimum thermal conductivity is obtained if flaky h-BN filler is oriented in parallel to heat flow. Since it is difficult to realize full orientation, the use of conglomerated h- BN filler is a suitable option. Optimum BD performance is obtained if void space is reduced by certain methods such as co-dispersion of different size fillers and addition of nano filler.

Original languageEnglish
Article number6118635
Pages (from-to)1973-1983
Number of pages11
JournalIEEE Transactions on Dielectrics and Electrical Insulation
Volume18
Issue number6
DOIs
Publication statusPublished - 2011 Dec

Fingerprint

Electric breakdown
Fillers
Thermal conductivity
Composite materials
Partial discharges
Surface treatment
Silica
Heat transfer

Keywords

  • AlN
  • BN
  • dielectricbreakdown
  • epoxy
  • microcomposite
  • Nanocomposite
  • silica
  • surface modification
  • thermal conductivity

ASJC Scopus subject areas

  • Electrical and Electronic Engineering

Cite this

Development of epoxy/BN composites with high thermal conductivity and sufficient dielectric breakdown strength part II-breakdown strength. / Wang, Zengbin; Iizuka, Tomonori; Kozako, Masahiro; Ohki, Yoshimichi; Tanaka, Toshikatsu.

In: IEEE Transactions on Dielectrics and Electrical Insulation, Vol. 18, No. 6, 6118635, 12.2011, p. 1973-1983.

Research output: Contribution to journalArticle

@article{ebe8d522481d4e49a4c1bc527808597b,
title = "Development of epoxy/BN composites with high thermal conductivity and sufficient dielectric breakdown strength part II-breakdown strength",
abstract = "The aim of this research is to find a way to achieve the epoxy composites with high thermal conductivity and acceptable dielectric breakdown (BD) strength. A value 12.3 W/m·K is the highest thermal conductivity obtained for epoxy composite in Part I. Dielectric breakdown performances such as short-time dielectric breakdown strength (BD strength), partial discharge (PD) resistance and BD time for composites were investigated in the Part II. In general, micro filler inclusion will increase thermal conductivity and decrease dielectric breakdown performance. Influencing factors are considered to be the orientation of filler, the content of void space, the content ratio in the case of co-mixing, the addition of nano filler, and filler surface modification. Twenty six kinds of composites were prepared in consideration of the above influencing factors. There are two options for most appropriate ones among the composites evaluated in the research. One is an epoxy/ conglomerated h-BN composite with co-loaded nano SiO 2 and micro AlN filler. It has 12.3 W/m·K in thermal conductivity, 75.1 kV peak/mm in BD strength and 260 {\%} of BD time for neat epoxy. It is most suitable when low BD strength and high thermal conductivity is needed. The other one is an epoxy/ h-BN composite with co-loaded nano silica and AlN filler for requirement of very high BD strength but lower thermal conductivity. Optimum thermal conductivity is obtained if flaky h-BN filler is oriented in parallel to heat flow. Since it is difficult to realize full orientation, the use of conglomerated h- BN filler is a suitable option. Optimum BD performance is obtained if void space is reduced by certain methods such as co-dispersion of different size fillers and addition of nano filler.",
keywords = "AlN, BN, dielectricbreakdown, epoxy, microcomposite, Nanocomposite, silica, surface modification, thermal conductivity",
author = "Zengbin Wang and Tomonori Iizuka and Masahiro Kozako and Yoshimichi Ohki and Toshikatsu Tanaka",
year = "2011",
month = "12",
doi = "10.1109/TDEI.2011.6118635",
language = "English",
volume = "18",
pages = "1973--1983",
journal = "IEEE Transactions on Dielectrics and Electrical Insulation",
issn = "1070-9878",
publisher = "Institute of Electrical and Electronics Engineers Inc.",
number = "6",

}

TY - JOUR

T1 - Development of epoxy/BN composites with high thermal conductivity and sufficient dielectric breakdown strength part II-breakdown strength

AU - Wang, Zengbin

AU - Iizuka, Tomonori

AU - Kozako, Masahiro

AU - Ohki, Yoshimichi

AU - Tanaka, Toshikatsu

PY - 2011/12

Y1 - 2011/12

N2 - The aim of this research is to find a way to achieve the epoxy composites with high thermal conductivity and acceptable dielectric breakdown (BD) strength. A value 12.3 W/m·K is the highest thermal conductivity obtained for epoxy composite in Part I. Dielectric breakdown performances such as short-time dielectric breakdown strength (BD strength), partial discharge (PD) resistance and BD time for composites were investigated in the Part II. In general, micro filler inclusion will increase thermal conductivity and decrease dielectric breakdown performance. Influencing factors are considered to be the orientation of filler, the content of void space, the content ratio in the case of co-mixing, the addition of nano filler, and filler surface modification. Twenty six kinds of composites were prepared in consideration of the above influencing factors. There are two options for most appropriate ones among the composites evaluated in the research. One is an epoxy/ conglomerated h-BN composite with co-loaded nano SiO 2 and micro AlN filler. It has 12.3 W/m·K in thermal conductivity, 75.1 kV peak/mm in BD strength and 260 % of BD time for neat epoxy. It is most suitable when low BD strength and high thermal conductivity is needed. The other one is an epoxy/ h-BN composite with co-loaded nano silica and AlN filler for requirement of very high BD strength but lower thermal conductivity. Optimum thermal conductivity is obtained if flaky h-BN filler is oriented in parallel to heat flow. Since it is difficult to realize full orientation, the use of conglomerated h- BN filler is a suitable option. Optimum BD performance is obtained if void space is reduced by certain methods such as co-dispersion of different size fillers and addition of nano filler.

AB - The aim of this research is to find a way to achieve the epoxy composites with high thermal conductivity and acceptable dielectric breakdown (BD) strength. A value 12.3 W/m·K is the highest thermal conductivity obtained for epoxy composite in Part I. Dielectric breakdown performances such as short-time dielectric breakdown strength (BD strength), partial discharge (PD) resistance and BD time for composites were investigated in the Part II. In general, micro filler inclusion will increase thermal conductivity and decrease dielectric breakdown performance. Influencing factors are considered to be the orientation of filler, the content of void space, the content ratio in the case of co-mixing, the addition of nano filler, and filler surface modification. Twenty six kinds of composites were prepared in consideration of the above influencing factors. There are two options for most appropriate ones among the composites evaluated in the research. One is an epoxy/ conglomerated h-BN composite with co-loaded nano SiO 2 and micro AlN filler. It has 12.3 W/m·K in thermal conductivity, 75.1 kV peak/mm in BD strength and 260 % of BD time for neat epoxy. It is most suitable when low BD strength and high thermal conductivity is needed. The other one is an epoxy/ h-BN composite with co-loaded nano silica and AlN filler for requirement of very high BD strength but lower thermal conductivity. Optimum thermal conductivity is obtained if flaky h-BN filler is oriented in parallel to heat flow. Since it is difficult to realize full orientation, the use of conglomerated h- BN filler is a suitable option. Optimum BD performance is obtained if void space is reduced by certain methods such as co-dispersion of different size fillers and addition of nano filler.

KW - AlN

KW - BN

KW - dielectricbreakdown

KW - epoxy

KW - microcomposite

KW - Nanocomposite

KW - silica

KW - surface modification

KW - thermal conductivity

UR - http://www.scopus.com/inward/record.url?scp=84862958747&partnerID=8YFLogxK

UR - http://www.scopus.com/inward/citedby.url?scp=84862958747&partnerID=8YFLogxK

U2 - 10.1109/TDEI.2011.6118635

DO - 10.1109/TDEI.2011.6118635

M3 - Article

AN - SCOPUS:84862958747

VL - 18

SP - 1973

EP - 1983

JO - IEEE Transactions on Dielectrics and Electrical Insulation

JF - IEEE Transactions on Dielectrics and Electrical Insulation

SN - 1070-9878

IS - 6

M1 - 6118635

ER -