Development of polyglycolic and polylactic acid fluid-loss control materials for fracturing fluids

Koichi Yoshimura, Hitoshi Matsui, Nobuo Morita

Research output: Chapter in Book/Report/Conference proceedingConference contribution

1 Citation (Scopus)

Abstract

Fluid-loss is significant for the standard fracturing-fluids without adding solid materials. One method to reduce fluid-loss is to add silica flour, although it reduces fracture conductivity. Other methods are to use wall building polymers. However, the fluid-loss is still significant and complete removal of wall building materials are not possible even with breakers. We found that powder, granular and fibrous materials made of Polyglycolic Acid (PGA) or Polylactic Acid (PLA) are very suitable for fluid-loss agents since they are as strong as rock, while they dissolve as liquid acids after applications. Fluid-loss tests are conducted using the standard API slot tester and filtrate loss tester, mixing powders, grains and fiber, all made of PGA or PLA in frac polymer fluids. Ratio of grains, powder and fiber is optimized to minimize fluid-loss for porous media and fractured porous media. Then, the changes of particle size are measured under heated conditions. Fracture simulation studies are also conducted using a 3D fracture boundary element model to compare the fluid efficiency of the fracturing fluids with and without the PLA and PGA particles. The results show that the capability of preventing fluid-loss and plugging micro-cracks is maintained for the porous filters and small slots within reasonable time period. For short term applications less than 3 hours, both PGA and PLA fluid-loss agents are stable when the temperature is less than 212°F. Mixing these materials often provides more efficient properties to reduce fluid-loss and to bridge micro-cracks. No residues are left after experiments if the fracturing fluid is kept being heated for 24 hours. The amount of the PGA and PLA fluid-loss agents required to reduce the fluid-loss is not significant. Hence, their field applications are feasible judging the cost and the benefit. The advantage in using these materials is that they turn from solid to liquid after applications so that no formation damage and no proppants conductivity damage occurs. The fluid-loss is also significantly reduced with the powder particles. In addition, because the PGA and PLA materials are degradable, solids with arbitrary sizes and shapes may be used as long as they control fluid-loss and plug fine fractures. Their applications are not only limited to reducing fluid-loss but they may be used for engineering fracture design to enhance the fracture conductivity.

Original languageEnglish
Title of host publicationSPE - European Formation Damage Conference, Proceedings, EFDC
PublisherSociety of Petroleum Engineers (SPE)
Pages722-745
Number of pages24
Volume2
ISBN (Print)9781632660824
Publication statusPublished - 2014
EventSPE International Symposium and Exhibition on Formation Damage Control 2014 - Lafayette, LA
Duration: 2014 Feb 262014 Feb 28

Other

OtherSPE International Symposium and Exhibition on Formation Damage Control 2014
CityLafayette, LA
Period14/2/2614/2/28

Fingerprint

Fracturing fluids
Fluids
Acids
fluid
acid
Powders
material
loss
conductivity
microcrack
Porous materials
porous medium
Cracks
polymer
Proppants
Fibers
Liquids
Polymers

ASJC Scopus subject areas

  • Energy Engineering and Power Technology
  • Geotechnical Engineering and Engineering Geology

Cite this

Yoshimura, K., Matsui, H., & Morita, N. (2014). Development of polyglycolic and polylactic acid fluid-loss control materials for fracturing fluids. In SPE - European Formation Damage Conference, Proceedings, EFDC (Vol. 2, pp. 722-745). Society of Petroleum Engineers (SPE).

Development of polyglycolic and polylactic acid fluid-loss control materials for fracturing fluids. / Yoshimura, Koichi; Matsui, Hitoshi; Morita, Nobuo.

SPE - European Formation Damage Conference, Proceedings, EFDC. Vol. 2 Society of Petroleum Engineers (SPE), 2014. p. 722-745.

Research output: Chapter in Book/Report/Conference proceedingConference contribution

Yoshimura, K, Matsui, H & Morita, N 2014, Development of polyglycolic and polylactic acid fluid-loss control materials for fracturing fluids. in SPE - European Formation Damage Conference, Proceedings, EFDC. vol. 2, Society of Petroleum Engineers (SPE), pp. 722-745, SPE International Symposium and Exhibition on Formation Damage Control 2014, Lafayette, LA, 14/2/26.
Yoshimura K, Matsui H, Morita N. Development of polyglycolic and polylactic acid fluid-loss control materials for fracturing fluids. In SPE - European Formation Damage Conference, Proceedings, EFDC. Vol. 2. Society of Petroleum Engineers (SPE). 2014. p. 722-745
Yoshimura, Koichi ; Matsui, Hitoshi ; Morita, Nobuo. / Development of polyglycolic and polylactic acid fluid-loss control materials for fracturing fluids. SPE - European Formation Damage Conference, Proceedings, EFDC. Vol. 2 Society of Petroleum Engineers (SPE), 2014. pp. 722-745
@inproceedings{1f74c36fdb344567874b77b33037a868,
title = "Development of polyglycolic and polylactic acid fluid-loss control materials for fracturing fluids",
abstract = "Fluid-loss is significant for the standard fracturing-fluids without adding solid materials. One method to reduce fluid-loss is to add silica flour, although it reduces fracture conductivity. Other methods are to use wall building polymers. However, the fluid-loss is still significant and complete removal of wall building materials are not possible even with breakers. We found that powder, granular and fibrous materials made of Polyglycolic Acid (PGA) or Polylactic Acid (PLA) are very suitable for fluid-loss agents since they are as strong as rock, while they dissolve as liquid acids after applications. Fluid-loss tests are conducted using the standard API slot tester and filtrate loss tester, mixing powders, grains and fiber, all made of PGA or PLA in frac polymer fluids. Ratio of grains, powder and fiber is optimized to minimize fluid-loss for porous media and fractured porous media. Then, the changes of particle size are measured under heated conditions. Fracture simulation studies are also conducted using a 3D fracture boundary element model to compare the fluid efficiency of the fracturing fluids with and without the PLA and PGA particles. The results show that the capability of preventing fluid-loss and plugging micro-cracks is maintained for the porous filters and small slots within reasonable time period. For short term applications less than 3 hours, both PGA and PLA fluid-loss agents are stable when the temperature is less than 212°F. Mixing these materials often provides more efficient properties to reduce fluid-loss and to bridge micro-cracks. No residues are left after experiments if the fracturing fluid is kept being heated for 24 hours. The amount of the PGA and PLA fluid-loss agents required to reduce the fluid-loss is not significant. Hence, their field applications are feasible judging the cost and the benefit. The advantage in using these materials is that they turn from solid to liquid after applications so that no formation damage and no proppants conductivity damage occurs. The fluid-loss is also significantly reduced with the powder particles. In addition, because the PGA and PLA materials are degradable, solids with arbitrary sizes and shapes may be used as long as they control fluid-loss and plug fine fractures. Their applications are not only limited to reducing fluid-loss but they may be used for engineering fracture design to enhance the fracture conductivity.",
author = "Koichi Yoshimura and Hitoshi Matsui and Nobuo Morita",
year = "2014",
language = "English",
isbn = "9781632660824",
volume = "2",
pages = "722--745",
booktitle = "SPE - European Formation Damage Conference, Proceedings, EFDC",
publisher = "Society of Petroleum Engineers (SPE)",

}

TY - GEN

T1 - Development of polyglycolic and polylactic acid fluid-loss control materials for fracturing fluids

AU - Yoshimura, Koichi

AU - Matsui, Hitoshi

AU - Morita, Nobuo

PY - 2014

Y1 - 2014

N2 - Fluid-loss is significant for the standard fracturing-fluids without adding solid materials. One method to reduce fluid-loss is to add silica flour, although it reduces fracture conductivity. Other methods are to use wall building polymers. However, the fluid-loss is still significant and complete removal of wall building materials are not possible even with breakers. We found that powder, granular and fibrous materials made of Polyglycolic Acid (PGA) or Polylactic Acid (PLA) are very suitable for fluid-loss agents since they are as strong as rock, while they dissolve as liquid acids after applications. Fluid-loss tests are conducted using the standard API slot tester and filtrate loss tester, mixing powders, grains and fiber, all made of PGA or PLA in frac polymer fluids. Ratio of grains, powder and fiber is optimized to minimize fluid-loss for porous media and fractured porous media. Then, the changes of particle size are measured under heated conditions. Fracture simulation studies are also conducted using a 3D fracture boundary element model to compare the fluid efficiency of the fracturing fluids with and without the PLA and PGA particles. The results show that the capability of preventing fluid-loss and plugging micro-cracks is maintained for the porous filters and small slots within reasonable time period. For short term applications less than 3 hours, both PGA and PLA fluid-loss agents are stable when the temperature is less than 212°F. Mixing these materials often provides more efficient properties to reduce fluid-loss and to bridge micro-cracks. No residues are left after experiments if the fracturing fluid is kept being heated for 24 hours. The amount of the PGA and PLA fluid-loss agents required to reduce the fluid-loss is not significant. Hence, their field applications are feasible judging the cost and the benefit. The advantage in using these materials is that they turn from solid to liquid after applications so that no formation damage and no proppants conductivity damage occurs. The fluid-loss is also significantly reduced with the powder particles. In addition, because the PGA and PLA materials are degradable, solids with arbitrary sizes and shapes may be used as long as they control fluid-loss and plug fine fractures. Their applications are not only limited to reducing fluid-loss but they may be used for engineering fracture design to enhance the fracture conductivity.

AB - Fluid-loss is significant for the standard fracturing-fluids without adding solid materials. One method to reduce fluid-loss is to add silica flour, although it reduces fracture conductivity. Other methods are to use wall building polymers. However, the fluid-loss is still significant and complete removal of wall building materials are not possible even with breakers. We found that powder, granular and fibrous materials made of Polyglycolic Acid (PGA) or Polylactic Acid (PLA) are very suitable for fluid-loss agents since they are as strong as rock, while they dissolve as liquid acids after applications. Fluid-loss tests are conducted using the standard API slot tester and filtrate loss tester, mixing powders, grains and fiber, all made of PGA or PLA in frac polymer fluids. Ratio of grains, powder and fiber is optimized to minimize fluid-loss for porous media and fractured porous media. Then, the changes of particle size are measured under heated conditions. Fracture simulation studies are also conducted using a 3D fracture boundary element model to compare the fluid efficiency of the fracturing fluids with and without the PLA and PGA particles. The results show that the capability of preventing fluid-loss and plugging micro-cracks is maintained for the porous filters and small slots within reasonable time period. For short term applications less than 3 hours, both PGA and PLA fluid-loss agents are stable when the temperature is less than 212°F. Mixing these materials often provides more efficient properties to reduce fluid-loss and to bridge micro-cracks. No residues are left after experiments if the fracturing fluid is kept being heated for 24 hours. The amount of the PGA and PLA fluid-loss agents required to reduce the fluid-loss is not significant. Hence, their field applications are feasible judging the cost and the benefit. The advantage in using these materials is that they turn from solid to liquid after applications so that no formation damage and no proppants conductivity damage occurs. The fluid-loss is also significantly reduced with the powder particles. In addition, because the PGA and PLA materials are degradable, solids with arbitrary sizes and shapes may be used as long as they control fluid-loss and plug fine fractures. Their applications are not only limited to reducing fluid-loss but they may be used for engineering fracture design to enhance the fracture conductivity.

UR - http://www.scopus.com/inward/record.url?scp=84903650215&partnerID=8YFLogxK

UR - http://www.scopus.com/inward/citedby.url?scp=84903650215&partnerID=8YFLogxK

M3 - Conference contribution

SN - 9781632660824

VL - 2

SP - 722

EP - 745

BT - SPE - European Formation Damage Conference, Proceedings, EFDC

PB - Society of Petroleum Engineers (SPE)

ER -