Distribution and thermal desorption behavior of hydrogen in titanium alloys immersed in acidic fluoride solutions

Toshio Ogawa, Ken'Ichi Yokoyama, Kenzo Asaoka, Jun'ichi Sakai

    Research output: Contribution to journalArticle

    25 Citations (Scopus)

    Abstract

    The distribution and thermal desorption behavior of hydrogen in alpha titanium (commercial pure titanium) and beta titanium alloy (Ti-11.3Mo-6.6Zr-4. 3Sn) immersed in acidic fluoride solutions (pH 5.0, 25 ± 2 °C) have been investigated. For alpha titanium, most of the hydrogen absorbed in the fluoride solution existed as titanium hydride within approximately 50 μm from the surface of the specimen. The local hydrogen concentration in the vicinity of the surface was evaluated above 5000 mass ppm. Hydrogen thermal desorption was observed in the temperature range from 200 to 700 °C. It is likely that the desorption at a low temperature resulted from the dissociation of the hydride, whereas that at a high temperature was caused by hydrogen strongly trapped in matrix defects induced by hydride formation. For the beta titanium alloy, the absorbed hydrogen diffused toward the center of the specimen without hydride forming. Hydrogen was almost uniformly distributed over the whole cross-section of the specimen, although hydrogen content was high at the surface layer of the specimen. Hydrogen desorption appeared in the range from 400 to 600 °C, implying that the absorbed hydrogen was mostly hydrogen in solution. The corrosion product (TiF3) on the surface of the specimen caused the desorption temperature to rise more than 100 °C, suggesting the origin of the scatter of desorption behavior.

    Original languageEnglish
    Pages (from-to)269-274
    Number of pages6
    JournalJournal of Alloys and Compounds
    Volume396
    Issue number1-2
    DOIs
    Publication statusPublished - 2005 Jun 21

    Fingerprint

    Thermal desorption
    Fluorides
    Titanium alloys
    Hydrogen
    Hydrides
    Desorption
    Titanium
    Temperature
    Corrosion

    Keywords

    • Corrosion
    • Fluoride
    • Hydrogen embrittlement
    • Thermal desorption analysis
    • Titanium

    ASJC Scopus subject areas

    • Metals and Alloys

    Cite this

    Distribution and thermal desorption behavior of hydrogen in titanium alloys immersed in acidic fluoride solutions. / Ogawa, Toshio; Yokoyama, Ken'Ichi; Asaoka, Kenzo; Sakai, Jun'ichi.

    In: Journal of Alloys and Compounds, Vol. 396, No. 1-2, 21.06.2005, p. 269-274.

    Research output: Contribution to journalArticle

    Ogawa, Toshio ; Yokoyama, Ken'Ichi ; Asaoka, Kenzo ; Sakai, Jun'ichi. / Distribution and thermal desorption behavior of hydrogen in titanium alloys immersed in acidic fluoride solutions. In: Journal of Alloys and Compounds. 2005 ; Vol. 396, No. 1-2. pp. 269-274.
    @article{e3bb96f2440f4d44867adffad844a50a,
    title = "Distribution and thermal desorption behavior of hydrogen in titanium alloys immersed in acidic fluoride solutions",
    abstract = "The distribution and thermal desorption behavior of hydrogen in alpha titanium (commercial pure titanium) and beta titanium alloy (Ti-11.3Mo-6.6Zr-4. 3Sn) immersed in acidic fluoride solutions (pH 5.0, 25 ± 2 °C) have been investigated. For alpha titanium, most of the hydrogen absorbed in the fluoride solution existed as titanium hydride within approximately 50 μm from the surface of the specimen. The local hydrogen concentration in the vicinity of the surface was evaluated above 5000 mass ppm. Hydrogen thermal desorption was observed in the temperature range from 200 to 700 °C. It is likely that the desorption at a low temperature resulted from the dissociation of the hydride, whereas that at a high temperature was caused by hydrogen strongly trapped in matrix defects induced by hydride formation. For the beta titanium alloy, the absorbed hydrogen diffused toward the center of the specimen without hydride forming. Hydrogen was almost uniformly distributed over the whole cross-section of the specimen, although hydrogen content was high at the surface layer of the specimen. Hydrogen desorption appeared in the range from 400 to 600 °C, implying that the absorbed hydrogen was mostly hydrogen in solution. The corrosion product (TiF3) on the surface of the specimen caused the desorption temperature to rise more than 100 °C, suggesting the origin of the scatter of desorption behavior.",
    keywords = "Corrosion, Fluoride, Hydrogen embrittlement, Thermal desorption analysis, Titanium",
    author = "Toshio Ogawa and Ken'Ichi Yokoyama and Kenzo Asaoka and Jun'ichi Sakai",
    year = "2005",
    month = "6",
    day = "21",
    doi = "10.1016/j.jallcom.2004.12.041",
    language = "English",
    volume = "396",
    pages = "269--274",
    journal = "Journal of Alloys and Compounds",
    issn = "0925-8388",
    publisher = "Elsevier BV",
    number = "1-2",

    }

    TY - JOUR

    T1 - Distribution and thermal desorption behavior of hydrogen in titanium alloys immersed in acidic fluoride solutions

    AU - Ogawa, Toshio

    AU - Yokoyama, Ken'Ichi

    AU - Asaoka, Kenzo

    AU - Sakai, Jun'ichi

    PY - 2005/6/21

    Y1 - 2005/6/21

    N2 - The distribution and thermal desorption behavior of hydrogen in alpha titanium (commercial pure titanium) and beta titanium alloy (Ti-11.3Mo-6.6Zr-4. 3Sn) immersed in acidic fluoride solutions (pH 5.0, 25 ± 2 °C) have been investigated. For alpha titanium, most of the hydrogen absorbed in the fluoride solution existed as titanium hydride within approximately 50 μm from the surface of the specimen. The local hydrogen concentration in the vicinity of the surface was evaluated above 5000 mass ppm. Hydrogen thermal desorption was observed in the temperature range from 200 to 700 °C. It is likely that the desorption at a low temperature resulted from the dissociation of the hydride, whereas that at a high temperature was caused by hydrogen strongly trapped in matrix defects induced by hydride formation. For the beta titanium alloy, the absorbed hydrogen diffused toward the center of the specimen without hydride forming. Hydrogen was almost uniformly distributed over the whole cross-section of the specimen, although hydrogen content was high at the surface layer of the specimen. Hydrogen desorption appeared in the range from 400 to 600 °C, implying that the absorbed hydrogen was mostly hydrogen in solution. The corrosion product (TiF3) on the surface of the specimen caused the desorption temperature to rise more than 100 °C, suggesting the origin of the scatter of desorption behavior.

    AB - The distribution and thermal desorption behavior of hydrogen in alpha titanium (commercial pure titanium) and beta titanium alloy (Ti-11.3Mo-6.6Zr-4. 3Sn) immersed in acidic fluoride solutions (pH 5.0, 25 ± 2 °C) have been investigated. For alpha titanium, most of the hydrogen absorbed in the fluoride solution existed as titanium hydride within approximately 50 μm from the surface of the specimen. The local hydrogen concentration in the vicinity of the surface was evaluated above 5000 mass ppm. Hydrogen thermal desorption was observed in the temperature range from 200 to 700 °C. It is likely that the desorption at a low temperature resulted from the dissociation of the hydride, whereas that at a high temperature was caused by hydrogen strongly trapped in matrix defects induced by hydride formation. For the beta titanium alloy, the absorbed hydrogen diffused toward the center of the specimen without hydride forming. Hydrogen was almost uniformly distributed over the whole cross-section of the specimen, although hydrogen content was high at the surface layer of the specimen. Hydrogen desorption appeared in the range from 400 to 600 °C, implying that the absorbed hydrogen was mostly hydrogen in solution. The corrosion product (TiF3) on the surface of the specimen caused the desorption temperature to rise more than 100 °C, suggesting the origin of the scatter of desorption behavior.

    KW - Corrosion

    KW - Fluoride

    KW - Hydrogen embrittlement

    KW - Thermal desorption analysis

    KW - Titanium

    UR - http://www.scopus.com/inward/record.url?scp=18844400611&partnerID=8YFLogxK

    UR - http://www.scopus.com/inward/citedby.url?scp=18844400611&partnerID=8YFLogxK

    U2 - 10.1016/j.jallcom.2004.12.041

    DO - 10.1016/j.jallcom.2004.12.041

    M3 - Article

    VL - 396

    SP - 269

    EP - 274

    JO - Journal of Alloys and Compounds

    JF - Journal of Alloys and Compounds

    SN - 0925-8388

    IS - 1-2

    ER -