Investigation of flow pattern downstream of spiral grooved runner cone in pump-turbine

T. Sano, M. Maekawa, N. Okamoto, H. Yano, Kazuyoshi Miyagawa

    Research output: Chapter in Book/Report/Conference proceedingConference contribution

    2 Citations (Scopus)

    Abstract

    High amplitude of pressure fluctuation is observed in a draft tube of a hydraulic turbine and a pump-turbine, for the case of partial load operation. Several methods had been reported to mitigate the amplitude so far, such as, air or water injection to the draft tube, fins on the draft tube surface, or runner replacement with optimized velocity profile at runner exit. However, several problems for each method can be considered, such as, negative influence on efficiency, high cost, technical difficulties for installation, and so on. To solve these problems and satisfy the demand for mitigating the amplitude of pressure fluctuation simultaneously, a new runner cone with spiral grooves on the surface was developed. It was developed with unsteady draft tube calculation based on Design of Experiment (DOE) method, and the effect was confirmed by model tests. Finally, developed runner cone was installed to the prototype pump turbine, and predicted performance was confirmed by on-site tests. However, the reason why the grooved runner cone can mitigate the amplitude of pressure fluctuation in draft tube was not clarified. Therefore, numerical investigation focusing around runner cone was carried out. As a result, it was clarified that the velocity profile at runner outlet was modified by the grooved runner cone, such as, reverse flow downstream of runner cone and tangential velocity was reduced. It means the shear stress between main stream and dead water core region was weakened, therefore, it can be estimated that the amplitude of draft pressure fluctuation was reduced.

    Original languageEnglish
    Title of host publicationIOP Conference Series: Earth and Environmental Science
    Volume15
    EditionPART
    DOIs
    Publication statusPublished - 2012
    Event26th IAHR Symposium on Hydraulic Machinery and Systems - Beijing, China
    Duration: 2012 Aug 192012 Aug 23

    Other

    Other26th IAHR Symposium on Hydraulic Machinery and Systems
    CountryChina
    CityBeijing
    Period12/8/1912/8/23

    Fingerprint

    flow pattern
    turbine
    pump
    velocity profile
    model test
    shear stress
    replacement
    hydraulics
    water
    air
    cost
    method
    experiment

    ASJC Scopus subject areas

    • Earth and Planetary Sciences(all)
    • Environmental Science(all)

    Cite this

    Sano, T., Maekawa, M., Okamoto, N., Yano, H., & Miyagawa, K. (2012). Investigation of flow pattern downstream of spiral grooved runner cone in pump-turbine. In IOP Conference Series: Earth and Environmental Science (PART ed., Vol. 15). [022019] https://doi.org/10.1088/1755-1315/15/2/022019

    Investigation of flow pattern downstream of spiral grooved runner cone in pump-turbine. / Sano, T.; Maekawa, M.; Okamoto, N.; Yano, H.; Miyagawa, Kazuyoshi.

    IOP Conference Series: Earth and Environmental Science. Vol. 15 PART. ed. 2012. 022019.

    Research output: Chapter in Book/Report/Conference proceedingConference contribution

    Sano, T, Maekawa, M, Okamoto, N, Yano, H & Miyagawa, K 2012, Investigation of flow pattern downstream of spiral grooved runner cone in pump-turbine. in IOP Conference Series: Earth and Environmental Science. PART edn, vol. 15, 022019, 26th IAHR Symposium on Hydraulic Machinery and Systems, Beijing, China, 12/8/19. https://doi.org/10.1088/1755-1315/15/2/022019
    Sano T, Maekawa M, Okamoto N, Yano H, Miyagawa K. Investigation of flow pattern downstream of spiral grooved runner cone in pump-turbine. In IOP Conference Series: Earth and Environmental Science. PART ed. Vol. 15. 2012. 022019 https://doi.org/10.1088/1755-1315/15/2/022019
    Sano, T. ; Maekawa, M. ; Okamoto, N. ; Yano, H. ; Miyagawa, Kazuyoshi. / Investigation of flow pattern downstream of spiral grooved runner cone in pump-turbine. IOP Conference Series: Earth and Environmental Science. Vol. 15 PART. ed. 2012.
    @inproceedings{5caf62a5b20242088500025c30ef1a3a,
    title = "Investigation of flow pattern downstream of spiral grooved runner cone in pump-turbine",
    abstract = "High amplitude of pressure fluctuation is observed in a draft tube of a hydraulic turbine and a pump-turbine, for the case of partial load operation. Several methods had been reported to mitigate the amplitude so far, such as, air or water injection to the draft tube, fins on the draft tube surface, or runner replacement with optimized velocity profile at runner exit. However, several problems for each method can be considered, such as, negative influence on efficiency, high cost, technical difficulties for installation, and so on. To solve these problems and satisfy the demand for mitigating the amplitude of pressure fluctuation simultaneously, a new runner cone with spiral grooves on the surface was developed. It was developed with unsteady draft tube calculation based on Design of Experiment (DOE) method, and the effect was confirmed by model tests. Finally, developed runner cone was installed to the prototype pump turbine, and predicted performance was confirmed by on-site tests. However, the reason why the grooved runner cone can mitigate the amplitude of pressure fluctuation in draft tube was not clarified. Therefore, numerical investigation focusing around runner cone was carried out. As a result, it was clarified that the velocity profile at runner outlet was modified by the grooved runner cone, such as, reverse flow downstream of runner cone and tangential velocity was reduced. It means the shear stress between main stream and dead water core region was weakened, therefore, it can be estimated that the amplitude of draft pressure fluctuation was reduced.",
    author = "T. Sano and M. Maekawa and N. Okamoto and H. Yano and Kazuyoshi Miyagawa",
    year = "2012",
    doi = "10.1088/1755-1315/15/2/022019",
    language = "English",
    volume = "15",
    booktitle = "IOP Conference Series: Earth and Environmental Science",
    edition = "PART",

    }

    TY - GEN

    T1 - Investigation of flow pattern downstream of spiral grooved runner cone in pump-turbine

    AU - Sano, T.

    AU - Maekawa, M.

    AU - Okamoto, N.

    AU - Yano, H.

    AU - Miyagawa, Kazuyoshi

    PY - 2012

    Y1 - 2012

    N2 - High amplitude of pressure fluctuation is observed in a draft tube of a hydraulic turbine and a pump-turbine, for the case of partial load operation. Several methods had been reported to mitigate the amplitude so far, such as, air or water injection to the draft tube, fins on the draft tube surface, or runner replacement with optimized velocity profile at runner exit. However, several problems for each method can be considered, such as, negative influence on efficiency, high cost, technical difficulties for installation, and so on. To solve these problems and satisfy the demand for mitigating the amplitude of pressure fluctuation simultaneously, a new runner cone with spiral grooves on the surface was developed. It was developed with unsteady draft tube calculation based on Design of Experiment (DOE) method, and the effect was confirmed by model tests. Finally, developed runner cone was installed to the prototype pump turbine, and predicted performance was confirmed by on-site tests. However, the reason why the grooved runner cone can mitigate the amplitude of pressure fluctuation in draft tube was not clarified. Therefore, numerical investigation focusing around runner cone was carried out. As a result, it was clarified that the velocity profile at runner outlet was modified by the grooved runner cone, such as, reverse flow downstream of runner cone and tangential velocity was reduced. It means the shear stress between main stream and dead water core region was weakened, therefore, it can be estimated that the amplitude of draft pressure fluctuation was reduced.

    AB - High amplitude of pressure fluctuation is observed in a draft tube of a hydraulic turbine and a pump-turbine, for the case of partial load operation. Several methods had been reported to mitigate the amplitude so far, such as, air or water injection to the draft tube, fins on the draft tube surface, or runner replacement with optimized velocity profile at runner exit. However, several problems for each method can be considered, such as, negative influence on efficiency, high cost, technical difficulties for installation, and so on. To solve these problems and satisfy the demand for mitigating the amplitude of pressure fluctuation simultaneously, a new runner cone with spiral grooves on the surface was developed. It was developed with unsteady draft tube calculation based on Design of Experiment (DOE) method, and the effect was confirmed by model tests. Finally, developed runner cone was installed to the prototype pump turbine, and predicted performance was confirmed by on-site tests. However, the reason why the grooved runner cone can mitigate the amplitude of pressure fluctuation in draft tube was not clarified. Therefore, numerical investigation focusing around runner cone was carried out. As a result, it was clarified that the velocity profile at runner outlet was modified by the grooved runner cone, such as, reverse flow downstream of runner cone and tangential velocity was reduced. It means the shear stress between main stream and dead water core region was weakened, therefore, it can be estimated that the amplitude of draft pressure fluctuation was reduced.

    UR - http://www.scopus.com/inward/record.url?scp=84874090496&partnerID=8YFLogxK

    UR - http://www.scopus.com/inward/citedby.url?scp=84874090496&partnerID=8YFLogxK

    U2 - 10.1088/1755-1315/15/2/022019

    DO - 10.1088/1755-1315/15/2/022019

    M3 - Conference contribution

    AN - SCOPUS:84874090496

    VL - 15

    BT - IOP Conference Series: Earth and Environmental Science

    ER -