Seismic response control of wooden house placed on sliding base

Satsuya Soda, Yuji Miyazu

    Research output: Chapter in Book/Report/Conference proceedingConference contribution

    1 Citation (Scopus)

    Abstract

    Proposed in this study is the positive use of a hybrid structural system to upgrade seismic safety of a variety of light weight low rise houses. It consists of, from the bottom to the top, a concrete mat foundation on the ground, a high polymer sheet, a solid reinforced concrete (RC) base and an upper structure equipped with oil dampers. The point of this structural system is that the RC base is allowed to slide when it is subject to extremely strong ground motion, decreasing the seismic force transmitted to the upper structure. Since there will be no sliding when the ground motion is not strong, oil dampers are also installed to let the system be also effective even for minor ground motions or strong winds. It will be shown that the dampers also work to keep maximum deflection of the upper structure within that the house could be used soon after even extremely strong ground motions. Based on some preliminary experimental studies, we confirmed that the sliding between the smoothly finished RC surface and high polymer sheet yields quite stable load-deflection relation. Therefore, the next thing we had to do was to find out the proper value for the friction coefficient. There are some basic requirements for the system. For one thing, the RC base should not slide when subject to strong wind. And the other, maximum acceleration at the upper floors should be no greater than 400 to 500 cm/s 2, which is a bit greater than that expected for normal base-isolated house but is enough to prevent not only the house from severe damages but also the equipments from shifting, toppling and falling down. We finally identified the optimum value for the friction coefficient to be 0.2, which could be realized by the combination of RC surface and ultra high molecular weight polyethylene (UHMWPE) sheet. The study consists of three parts. First, we briefly explain how a proposed hybrid seismic response control system expected to work. Then, dealt with are analytical and experimental studies to identify a proper value for the friction coefficient of the sliding base. And finally, described are shaking table test and an analytical study to confirm the usefulness of the system in seismic design of wooden houses.

    Original languageEnglish
    Title of host publication9th US National and 10th Canadian Conference on Earthquake Engineering 2010, Including Papers from the 4th International Tsunami Symposium
    Pages1429-1436
    Number of pages8
    Volume2
    Publication statusPublished - 2010
    Event9th US National and 10th Canadian Conference on Earthquake Engineering 2010, Including Papers from the 4th International Tsunami Symposium - Toronto, ON
    Duration: 2010 Jul 252010 Jul 29

    Other

    Other9th US National and 10th Canadian Conference on Earthquake Engineering 2010, Including Papers from the 4th International Tsunami Symposium
    CityToronto, ON
    Period10/7/2510/7/29

    Fingerprint

    Seismic response
    Reinforced concrete
    Friction
    Ultrahigh molecular weight polyethylenes
    Seismic design
    Polymers
    Concretes
    Control systems
    Oils

    ASJC Scopus subject areas

    • Environmental Engineering

    Cite this

    Soda, S., & Miyazu, Y. (2010). Seismic response control of wooden house placed on sliding base. In 9th US National and 10th Canadian Conference on Earthquake Engineering 2010, Including Papers from the 4th International Tsunami Symposium (Vol. 2, pp. 1429-1436)

    Seismic response control of wooden house placed on sliding base. / Soda, Satsuya; Miyazu, Yuji.

    9th US National and 10th Canadian Conference on Earthquake Engineering 2010, Including Papers from the 4th International Tsunami Symposium. Vol. 2 2010. p. 1429-1436.

    Research output: Chapter in Book/Report/Conference proceedingConference contribution

    Soda, S & Miyazu, Y 2010, Seismic response control of wooden house placed on sliding base. in 9th US National and 10th Canadian Conference on Earthquake Engineering 2010, Including Papers from the 4th International Tsunami Symposium. vol. 2, pp. 1429-1436, 9th US National and 10th Canadian Conference on Earthquake Engineering 2010, Including Papers from the 4th International Tsunami Symposium, Toronto, ON, 10/7/25.
    Soda S, Miyazu Y. Seismic response control of wooden house placed on sliding base. In 9th US National and 10th Canadian Conference on Earthquake Engineering 2010, Including Papers from the 4th International Tsunami Symposium. Vol. 2. 2010. p. 1429-1436
    Soda, Satsuya ; Miyazu, Yuji. / Seismic response control of wooden house placed on sliding base. 9th US National and 10th Canadian Conference on Earthquake Engineering 2010, Including Papers from the 4th International Tsunami Symposium. Vol. 2 2010. pp. 1429-1436
    @inproceedings{22e9d989d30349b680bb9edd391dd873,
    title = "Seismic response control of wooden house placed on sliding base",
    abstract = "Proposed in this study is the positive use of a hybrid structural system to upgrade seismic safety of a variety of light weight low rise houses. It consists of, from the bottom to the top, a concrete mat foundation on the ground, a high polymer sheet, a solid reinforced concrete (RC) base and an upper structure equipped with oil dampers. The point of this structural system is that the RC base is allowed to slide when it is subject to extremely strong ground motion, decreasing the seismic force transmitted to the upper structure. Since there will be no sliding when the ground motion is not strong, oil dampers are also installed to let the system be also effective even for minor ground motions or strong winds. It will be shown that the dampers also work to keep maximum deflection of the upper structure within that the house could be used soon after even extremely strong ground motions. Based on some preliminary experimental studies, we confirmed that the sliding between the smoothly finished RC surface and high polymer sheet yields quite stable load-deflection relation. Therefore, the next thing we had to do was to find out the proper value for the friction coefficient. There are some basic requirements for the system. For one thing, the RC base should not slide when subject to strong wind. And the other, maximum acceleration at the upper floors should be no greater than 400 to 500 cm/s 2, which is a bit greater than that expected for normal base-isolated house but is enough to prevent not only the house from severe damages but also the equipments from shifting, toppling and falling down. We finally identified the optimum value for the friction coefficient to be 0.2, which could be realized by the combination of RC surface and ultra high molecular weight polyethylene (UHMWPE) sheet. The study consists of three parts. First, we briefly explain how a proposed hybrid seismic response control system expected to work. Then, dealt with are analytical and experimental studies to identify a proper value for the friction coefficient of the sliding base. And finally, described are shaking table test and an analytical study to confirm the usefulness of the system in seismic design of wooden houses.",
    author = "Satsuya Soda and Yuji Miyazu",
    year = "2010",
    language = "English",
    isbn = "9781617388446",
    volume = "2",
    pages = "1429--1436",
    booktitle = "9th US National and 10th Canadian Conference on Earthquake Engineering 2010, Including Papers from the 4th International Tsunami Symposium",

    }

    TY - GEN

    T1 - Seismic response control of wooden house placed on sliding base

    AU - Soda, Satsuya

    AU - Miyazu, Yuji

    PY - 2010

    Y1 - 2010

    N2 - Proposed in this study is the positive use of a hybrid structural system to upgrade seismic safety of a variety of light weight low rise houses. It consists of, from the bottom to the top, a concrete mat foundation on the ground, a high polymer sheet, a solid reinforced concrete (RC) base and an upper structure equipped with oil dampers. The point of this structural system is that the RC base is allowed to slide when it is subject to extremely strong ground motion, decreasing the seismic force transmitted to the upper structure. Since there will be no sliding when the ground motion is not strong, oil dampers are also installed to let the system be also effective even for minor ground motions or strong winds. It will be shown that the dampers also work to keep maximum deflection of the upper structure within that the house could be used soon after even extremely strong ground motions. Based on some preliminary experimental studies, we confirmed that the sliding between the smoothly finished RC surface and high polymer sheet yields quite stable load-deflection relation. Therefore, the next thing we had to do was to find out the proper value for the friction coefficient. There are some basic requirements for the system. For one thing, the RC base should not slide when subject to strong wind. And the other, maximum acceleration at the upper floors should be no greater than 400 to 500 cm/s 2, which is a bit greater than that expected for normal base-isolated house but is enough to prevent not only the house from severe damages but also the equipments from shifting, toppling and falling down. We finally identified the optimum value for the friction coefficient to be 0.2, which could be realized by the combination of RC surface and ultra high molecular weight polyethylene (UHMWPE) sheet. The study consists of three parts. First, we briefly explain how a proposed hybrid seismic response control system expected to work. Then, dealt with are analytical and experimental studies to identify a proper value for the friction coefficient of the sliding base. And finally, described are shaking table test and an analytical study to confirm the usefulness of the system in seismic design of wooden houses.

    AB - Proposed in this study is the positive use of a hybrid structural system to upgrade seismic safety of a variety of light weight low rise houses. It consists of, from the bottom to the top, a concrete mat foundation on the ground, a high polymer sheet, a solid reinforced concrete (RC) base and an upper structure equipped with oil dampers. The point of this structural system is that the RC base is allowed to slide when it is subject to extremely strong ground motion, decreasing the seismic force transmitted to the upper structure. Since there will be no sliding when the ground motion is not strong, oil dampers are also installed to let the system be also effective even for minor ground motions or strong winds. It will be shown that the dampers also work to keep maximum deflection of the upper structure within that the house could be used soon after even extremely strong ground motions. Based on some preliminary experimental studies, we confirmed that the sliding between the smoothly finished RC surface and high polymer sheet yields quite stable load-deflection relation. Therefore, the next thing we had to do was to find out the proper value for the friction coefficient. There are some basic requirements for the system. For one thing, the RC base should not slide when subject to strong wind. And the other, maximum acceleration at the upper floors should be no greater than 400 to 500 cm/s 2, which is a bit greater than that expected for normal base-isolated house but is enough to prevent not only the house from severe damages but also the equipments from shifting, toppling and falling down. We finally identified the optimum value for the friction coefficient to be 0.2, which could be realized by the combination of RC surface and ultra high molecular weight polyethylene (UHMWPE) sheet. The study consists of three parts. First, we briefly explain how a proposed hybrid seismic response control system expected to work. Then, dealt with are analytical and experimental studies to identify a proper value for the friction coefficient of the sliding base. And finally, described are shaking table test and an analytical study to confirm the usefulness of the system in seismic design of wooden houses.

    UR - http://www.scopus.com/inward/record.url?scp=84867149458&partnerID=8YFLogxK

    UR - http://www.scopus.com/inward/citedby.url?scp=84867149458&partnerID=8YFLogxK

    M3 - Conference contribution

    AN - SCOPUS:84867149458

    SN - 9781617388446

    VL - 2

    SP - 1429

    EP - 1436

    BT - 9th US National and 10th Canadian Conference on Earthquake Engineering 2010, Including Papers from the 4th International Tsunami Symposium

    ER -