Three-dimensional noise mapping system with aerial blimp robot

Ryouzi Saitou, Yusuke Ikeda, Yasuhiro Oikawa

    Research output: Contribution to journalConference article

    1 Citation (Scopus)

    Abstract

    This paper presents a prototype system of a three-dimensional noise mapping system with an aerial blimp robot. The system's length is 1.5 m, its width is approximately 1.2 m, and its weight is approximately 850 g. The system is divided into two parts; one part is a balloon filled with helium gas, and the other part is a multirotor unit. Since the balloon helps to hover in the air without rotating propellers, the propeller rotation noise can be reduced. The buoyancy of helium gas is lighter than the system weight and therefore the system could return to the ground automatically, even when it is out of control caused by low battery or other problems. The multirotor unit has six propellers, which make enable omnidirectional motion. The multirotor unit also has a system control board with a field programmable gate array system on chip, which integrates central processing unit for controlling of propeller rotation, sound recording, and communicating with the host personal computer. The microphone for recording the sound is mounted at the middle of the balloon, to reduce the effect of propeller rotation noise. We evaluated the system two ways: a comparison of the propeller rotation noises between the system and a general multirotor, and an analysis of acoustical effect of the balloon. The result showed that the propeller rotation noise was reduced by 42 dB as compared with a general multirotor, and the balloon had large effects of the sound field when the balloon was placed between the sound source and the microphone. Finally, we measured the sound pressure level using the proposed system. The result showed that the proposed system can continuously measure sound pressure distribution in noise map space.

    Original languageEnglish
    Article number040006
    JournalProceedings of Meetings on Acoustics
    Volume29
    Issue number1
    DOIs
    Publication statusPublished - 2016 Nov 28
    Event172nd Meeting of the Acoustical Society of America - Honolulu, United States
    Duration: 2016 Nov 282016 Dec 2

    Fingerprint

    propellers
    robots
    balloons
    sound pressure
    microphones
    acoustics
    recording
    helium
    control boards
    communicating
    field-programmable gate arrays
    personal computers
    sound fields
    gases
    pressure distribution
    buoyancy
    central processing units
    electric batteries
    chips
    prototypes

    ASJC Scopus subject areas

    • Acoustics and Ultrasonics

    Cite this

    Three-dimensional noise mapping system with aerial blimp robot. / Saitou, Ryouzi; Ikeda, Yusuke; Oikawa, Yasuhiro.

    In: Proceedings of Meetings on Acoustics, Vol. 29, No. 1, 040006, 28.11.2016.

    Research output: Contribution to journalConference article

    @article{414eba87e9964140b348acf5949374ff,
    title = "Three-dimensional noise mapping system with aerial blimp robot",
    abstract = "This paper presents a prototype system of a three-dimensional noise mapping system with an aerial blimp robot. The system's length is 1.5 m, its width is approximately 1.2 m, and its weight is approximately 850 g. The system is divided into two parts; one part is a balloon filled with helium gas, and the other part is a multirotor unit. Since the balloon helps to hover in the air without rotating propellers, the propeller rotation noise can be reduced. The buoyancy of helium gas is lighter than the system weight and therefore the system could return to the ground automatically, even when it is out of control caused by low battery or other problems. The multirotor unit has six propellers, which make enable omnidirectional motion. The multirotor unit also has a system control board with a field programmable gate array system on chip, which integrates central processing unit for controlling of propeller rotation, sound recording, and communicating with the host personal computer. The microphone for recording the sound is mounted at the middle of the balloon, to reduce the effect of propeller rotation noise. We evaluated the system two ways: a comparison of the propeller rotation noises between the system and a general multirotor, and an analysis of acoustical effect of the balloon. The result showed that the propeller rotation noise was reduced by 42 dB as compared with a general multirotor, and the balloon had large effects of the sound field when the balloon was placed between the sound source and the microphone. Finally, we measured the sound pressure level using the proposed system. The result showed that the proposed system can continuously measure sound pressure distribution in noise map space.",
    author = "Ryouzi Saitou and Yusuke Ikeda and Yasuhiro Oikawa",
    year = "2016",
    month = "11",
    day = "28",
    doi = "10.1121/2.0000417",
    language = "English",
    volume = "29",
    journal = "Proceedings of Meetings on Acoustics",
    issn = "1939-800X",
    publisher = "Acoustical Society of America",
    number = "1",

    }

    TY - JOUR

    T1 - Three-dimensional noise mapping system with aerial blimp robot

    AU - Saitou, Ryouzi

    AU - Ikeda, Yusuke

    AU - Oikawa, Yasuhiro

    PY - 2016/11/28

    Y1 - 2016/11/28

    N2 - This paper presents a prototype system of a three-dimensional noise mapping system with an aerial blimp robot. The system's length is 1.5 m, its width is approximately 1.2 m, and its weight is approximately 850 g. The system is divided into two parts; one part is a balloon filled with helium gas, and the other part is a multirotor unit. Since the balloon helps to hover in the air without rotating propellers, the propeller rotation noise can be reduced. The buoyancy of helium gas is lighter than the system weight and therefore the system could return to the ground automatically, even when it is out of control caused by low battery or other problems. The multirotor unit has six propellers, which make enable omnidirectional motion. The multirotor unit also has a system control board with a field programmable gate array system on chip, which integrates central processing unit for controlling of propeller rotation, sound recording, and communicating with the host personal computer. The microphone for recording the sound is mounted at the middle of the balloon, to reduce the effect of propeller rotation noise. We evaluated the system two ways: a comparison of the propeller rotation noises between the system and a general multirotor, and an analysis of acoustical effect of the balloon. The result showed that the propeller rotation noise was reduced by 42 dB as compared with a general multirotor, and the balloon had large effects of the sound field when the balloon was placed between the sound source and the microphone. Finally, we measured the sound pressure level using the proposed system. The result showed that the proposed system can continuously measure sound pressure distribution in noise map space.

    AB - This paper presents a prototype system of a three-dimensional noise mapping system with an aerial blimp robot. The system's length is 1.5 m, its width is approximately 1.2 m, and its weight is approximately 850 g. The system is divided into two parts; one part is a balloon filled with helium gas, and the other part is a multirotor unit. Since the balloon helps to hover in the air without rotating propellers, the propeller rotation noise can be reduced. The buoyancy of helium gas is lighter than the system weight and therefore the system could return to the ground automatically, even when it is out of control caused by low battery or other problems. The multirotor unit has six propellers, which make enable omnidirectional motion. The multirotor unit also has a system control board with a field programmable gate array system on chip, which integrates central processing unit for controlling of propeller rotation, sound recording, and communicating with the host personal computer. The microphone for recording the sound is mounted at the middle of the balloon, to reduce the effect of propeller rotation noise. We evaluated the system two ways: a comparison of the propeller rotation noises between the system and a general multirotor, and an analysis of acoustical effect of the balloon. The result showed that the propeller rotation noise was reduced by 42 dB as compared with a general multirotor, and the balloon had large effects of the sound field when the balloon was placed between the sound source and the microphone. Finally, we measured the sound pressure level using the proposed system. The result showed that the proposed system can continuously measure sound pressure distribution in noise map space.

    UR - http://www.scopus.com/inward/record.url?scp=85042162872&partnerID=8YFLogxK

    UR - http://www.scopus.com/inward/citedby.url?scp=85042162872&partnerID=8YFLogxK

    U2 - 10.1121/2.0000417

    DO - 10.1121/2.0000417

    M3 - Conference article

    AN - SCOPUS:85042162872

    VL - 29

    JO - Proceedings of Meetings on Acoustics

    JF - Proceedings of Meetings on Acoustics

    SN - 1939-800X

    IS - 1

    M1 - 040006

    ER -